RS_1

1930s- Style Rear Buggy Spring

RS_1 Rear Buggy Spring, circa 1930s Work great for Rat Rods, Street Rods, Jalopies, and Super Modified type builds.

Just $ .50 each plus shipping.

RS_2

Transverse Spring Perch

The RS_2 is a cool old school universal spring perch for buggy spring set ups. Check out the detail! Overall measurements are as follows; length = 13mm, width = 9mm, and height = 5.8mm. Designed and 3D resin printed by Ron Coon Resins.

Just $1.75 each plus shipping.

RS_3

Leaf Springs

The RS_3 is a leaf spring designed and 3D resin printed by WFC Motorsports. With its great detail the RS_3 would be a great addition to any build in need of leaf springs.

Overall length is 44.8mm, perch is designed for 1/8″ axle tube.

Just $2.76 per pair, plus shipping.

RS_4

Leaf Springs

The RS_4 is a leaf spring designed and 3D resin printed by WFC Motorsports. With its great detail the RS_4 would be a great addition to any build in need of leaf springs.

Overall length is 54.25mm, perch is designed for 1/8″ axle tube.

Just $2.76 per pair, plus shipping.

RS_5

1930’s Style Front Parallel/Transverse Spring

The RS_5 is a must for those Rat Rods, Street Rods, Jalopies, and Super Modified type builds. Designed by Nahuel Customs and 3D resin printed by Ron Coon Resins. Overall measurements are Length = 34.6mm, Height = 4.6mm, and Depth = 3.0mm

Just $2.00 per pair each plus shipping.

RS_4

Leaf Springs

The RS_4 is a leaf spring designed and 3D resin printed by WFC Motorsports. With its great detail the RS_4 would be a great addition to any build in need of leaf springs.

Overall length is 54.25mm, perch is designed for 1/8″ axle tube.

Just $2.76 per pair, plus shipping.

SP_1

Spindle for AMT/ERTL NASCAR Chassis

The SP_1 is a Spindle for both scratch and kit builders. It is designed to fit AMT/ERTL 1:25 scale NASCAR chassis, replacing the kit spindle when either aftermarket or kit spud type backing plates are to be used. The SP_1 has been fabricated to keep kit ride height intact. For best fit, it is recommended backing plate spud be drilled out to 1/16”. Designed and 3D resin printed by Ron Coon Resins.

Just $1.14 per pair, plus shipping.

Item painted for display purposes, item comes bare resin.

SP_2

Drop Spindle For AMT/ERTL NASCAR Chassis

The SP_2 is a Spindle for both scratch and kit builders. It is designed to fit AMT/ERTL 1:25 scale NASCAR chassis, replacing the kit spindle when either aftermarket or kit spud type backing plates are to be used. The SP_2 has been fabricated to lower the kit height approximately a good  1mm. For best fit it is recommended that the backing plate spud be drilled out to 1/16”. Designed and 3D resin printed by Ron Coon Resins.

Just $1.14 per pair, plus shipping. 

Item painted for display purposes, comes bare resin.

SK_1

7″ Conventional Front Shock

The SK_1 was designed as a front 7” shock but could be used as for any applicable application. The SK_1 measures 17mm center to center of mounting holes. Designed and 3D resin printed by Ron Coon Resins.

Just $1.29 per pair plus shipping.

SK_2

9″ Conventional Front Shock

The SK_2 was designed as a rear 9” shock but could be used as for any applicable application. The SK_2 measures 19mm center to center of mounting holes. Designed and 3D resin printed by Ron Coon Resins.

Just $1.29 per pair plus shipping.

SK_3

7″ Conventional Front Shock With Travel Indicator Ring

The SK_3 was designed as a front 7” shock with travel indicator ring but could be used as for any applicable application. The SK_3 measures 17mm center to center of mounting holes. Designed and 3D resin printed by Ron Coon Resins.

Just $1.49 per pair plus shipping.

SK_4

9″ Conventional Front Shock With Travel Indicator Ring

The SK_4 was designed as a rear 9” shock with travel indicator ring but could be used as for any applicable application. The SK_4 measures 19mm center to center of mounting holes. Designed and 3D resin printed by Ron Coon Resins.

Just $1.49 per pair plus shipping.

FL_1

Rear End 4 Links

The Fl_1 was designed for any race car using a 4 link rear suspension set such as Late Models and IMCA/UMP type Modifieds. Huge time saver for builders! Birdcages are designed to fit all Ron Coon Resins quick change rear ends and or 1/8″ rear end tubes. Designed and 3D printed by WFC Motorsports. Distance from front of mounting bracket to axle center line is 12.2mm.

Just $2.76 per pair plus shipping.

RR_1

Wishbone Radius Rods

The RR_1 is a set of two rear and two front wishbone style radius rods found on vintage Super Modifieds and Sprints. The RR_1 would also work well with Rat and Street Rod builds. Overall length dimensions are as follows; Front = 1 1/2″, Rear = 1 7/8″.

Just $3.25 per set, plus shipping.

Item comes bare resin.

RR_4

 Axle Bracket

The RR_4 was designed for builders that want to build 2 or 3 link style rear suspensions. Has front and rear mounts for shock and or coil spring as well as mounting spud for radius rod. Fits 1/8″ axle tube. Use HJ_3 heim joint to mount radius rod to bracket spud.  The RR_4 measures 7.47mm from center of axle to center of shock/spring mounts. Designed and 3D resin printed by Ron Coon Resins.

Just $2.25 per pair plus shipping.

Item comes on supports

RR_5

5 Hole Radius Rod Bracket

The RR_5 is a 5 hole radius rod bracket that could be used for many different divisions of circle track, drag, or street builds. It is designed for builders who want the option of locating radius rods at different angles and moving suspension. Use HJ_1 heim joints with the RR_5 bracket. Straight pins or micro bolts will be needed to be used to assemble. Overall dimensions are height = 11mm, width = 2.72mm, and depth = 5.5mm. Designed and 3D resin printed by Ron Coon Resins.

Just $2.25 per pair plus shipping.

Item comes on supports

RR_6

5 Hole Radius Rod Bracket

The RR_6 is a 5 hole radius rod bracket that could be used for many different divisions of circle track, drag, or street builds. It is designed for builders who are not interested in moving suspension. Designed with stationary bolt head on one side and nut and bolt on the opposite side. Use HJ_3 heim joints with the RR_5 bracket. Overall dimensions are height = 11mm, width = 4.25mm, and depth = 5.5mm. Designed and 3D resin printed by Ron Coon Resins.

Just $2.25 per pair plus shipping.

Item comes on supports

RR_7

3 Hole Radius Rod Bracket

The RR_7 is a 3 hole radius rod bracket that could be used for many different divisions of circle track, drag, or street builds. It is designed for builders who want the option of locating radius rods at different angles and moving suspension. Use HJ_1 heim joints with the RR_7 bracket. Overall dimensions are height = 7.25mm, width = 2.72mm, and depth = 4.2mm. Designed and 3D resin printed by Ron Coon Resins.

Just $2.10 per pair plus shipping.

Item comes on supports

RR_8

3 Hole Radius Rod Bracket

The RR_8 is a 3 hole radius rod bracket that could be used for many different divisions of circle track, drag, or street builds. It is designed for builders who are not interested in moving suspension. Designed with stationary bolt head on one side and nut and bolt on the opposite side Use HJ_3 heim joints with the RR_8 bracket. Overall dimensions are height = 7.25mm, width = 4.25mm, and depth = 4.2mm. Designed and 3D resin printed by Ron Coon Resins.

Just $2.10 per pair plus shipping.

Item comes on supports

RR_9

J Bar Bracket

The RR_9 is a pinion mounted J Bar bracket like you see on many different types of circle track cars. Designed and 3D resin printed by Ron Coon Resins. Overall dimensions are width = 10.7mm, height = 8mm, depth = 1mm.

Best choice of heim joint to be used with the RR_9 is the HJ_2.

Just $.75 each plus shipping.

Rear end with bracket not included. Item comes on supports.

RR_10

J Bar / Panhard Bar Slider Mount

The RR_10 is a J Bar / Panhard bar slider mount. Can be used on any circle track build that uses a J Bar or Panhard bar set up to center the rear end. Designed and 3D resin printed by Ron Coon Resins to fit Evergreen #212 2mm rod. Overall dimensions are width = 5mm, height = 8mm, depth = 6.75mm

Best choice of heim joint for the RR_10 is the HJ_2.

Just $1.25 per assembly plus shipping.

RR_11

Torque Link & Rear End Bracket

The RR_11 is an old school AFCO style small spring torque link aka pull spring with a rear end bracket designed to fit 1:25 kit Ford 9 inch rear ends. Designed and 3D printed by Ron Coon Resins. Torque link stud is made to fit K&S 1/16″ aluminum tubing. NOTE: mounting bracket is designed with an angle to it. When placed on top of rear end, torque link mounting pins should be to the rear side of the axle center line, if not rotate bracket 180 degrees. Assembly consists of 1 torque link and 1 rear end bracket.

Just $2.75 per assembly plus shipping.

Item comes on supports.

HJ_2

Heim Joints

The HJ_2 is a heim joint designed for builders who want to glue their heim joints to a spud or item that the backside is not visible such as a pitman arm. Heim has stationary bolt and nut on one side and flat surface on the opposite side. Designed and 3D printed by Ron Coon Resins to fit K&S 1/16″ aluminum tubing. Works RR_4 axle bracket and solid spuds.

Just $1.99 per set of 4 plus shipping.

Aluminum tube not included. Item comes on supports.

HJ_1

Heim Joints

The HJ_1 is a heim joint designed for builders who want to either pin or micro bolt their heim joints. The HJ_1 is perfect for radius rods, panhard bars, j bars, pull bars, tie rods, and pitman rods.  Bolt hole goes completely through heim. Designed and 3D printed by Ron Coon Resins to fit K&S 1/16″ aluminum tubing. Works with radius rod brackets RR_5 and RR_7.

Just $1.99 per set of 4 plus shipping.

Aluminum tube not included. Item comes on supports.

HJ_2

Heim Joints

The HJ_2 is a heim joint designed for builders who want to glue their heim joints to a spud or item that the backside is not visible such as a pitman arm. Heim has stationary bolt and nut on one side and flat surface on the opposite side. Designed and 3D printed by Ron Coon Resins to fit K&S 1/16″ aluminum tubing. Works RR_4 axle bracket and solid spuds.

Just $1.99 per set of 4 plus shipping.

Aluminum tube not included. Item comes on supports.

HJ_3

Heim Joints

The HJ_3 is a heim joint designed for builders who want to glue their heim joints in an area where neither side of the heim joint is visible.. Heim has flat surfaces on both sides for maximum gluing surface.. Designed and 3D printed by Ron Coon Resins to fit K&S 1/16″ aluminum tubing. Works with brackets RR_6 and RR_8.

Just $1.99 per set of 4 plus shipping.

Aluminum tube not included. Item comes on supports.