Engine Parts & Accessories
Need an ignition box, spark plug wire or an air cleaner for your Circle Track build? Look no further: We have it here!
AC_1
Old School Air Cleaner
AC_1 Here is our Old School Air Cleaner. It’s perfect for early Modifieds, Stock Cars, and Jalopies.
Just $1.20 each plus shipping.
AC_2
Air Cleaner for NASCAR, Street Stock, Hobby Stock
AC_2 If you are looking for that Circle Track look whether it be dirt or pavement then this is the Air Cleaner for you. It’s perfect for NASCAR, Street Stock, Hobby Stock, etc .
Just $1.20 each plus shipping.
AC_3
3 Carb Air Cleaner
AC_3 Gotta have a 3 carb set up? If you do, we have an Air Cleaner for you!
Just $1.25 plus shipping.
AC_4
Injector Motor Air Cleaners
AC_4 Have an Injector Motor and need some Air Cleaners? If so here ya go! 1:24 scale Sprint Car, but could be used for many injector applications.
Just $1.75 per set of four, plus shipping.
AC_5
2 Carb Air Cleaner
AC_5 Need an air cleaner for a 2 carb set up? If you do, we have an air cleaner for you!
Just $1.25 plus shipping.
AC_6
Circle Track Air Cleaner
AC_6 Air cleaner with the Circle Track builder in mind. Comes with 2 different covers, the base has built in riser that can be modified if needed, in scale approximately 14″ x 6″ just like the big boys are running! Overall height is 1/2″, diameter at bottom of plate is 5/8″.
Just $2.75 plus shipping.
AC_7
Air Cleaner With Outerwear Bag
The AC_7 uses an AC_6 element minus the carb riser, Moroso style top, wrapped with an Outerwear style textured element bag.
Just $1.75 plus shipping.
Item is painted and detailed for display purposes only, comes bare white resin.
AC_8
MOROSO Air Cleaner With Thin Element
AC_8 The infamous MOROSO style Air Cleaner with thin element, perfect for use with cold air boxes or low clearance situations.
Just $1.25 plus shipping.
Detailed for photo purposes, item comes as bare resin.
AC_9
K&N X-Stream Style Air Cleaner
The AC_9 is a K&N X-Stream Style Air Cleaner. You better run bigger jets if you plan on using this air cleaner!
Just $1.75 each plus shipping.
Item detailed for display purposes, item comes bare resin.
AC_10
Universal Air Cleaner
The AC_10 is a great all around 1:25 / 1:24 scale air cleaner. Use it on Circle Track, Drag, or Street builds. Overall dimensions are Height = 7mm, and Diameter = 15mm. Designed and 3D printed by Ron Coon Resins..
Just $1.75 plus shipping.
AC_11
Universal Air Cleaner
The AC_11 is a great all around 1:25 / 1:24 scale air cleaner. Use it on Circle Track, Drag, or Street builds. Overall dimensions are Height = 7.4mm, and Diameter = 15mm. Designed and 3D printed by Ron Coon Resins.
Just $1.75 plus shipping.
AC_12
Low Profile Air Cleaner
The AC_12 is a great 1:25 / 1:24 scale low profile air cleaner. Use it on Circle Track, Drag, or Street builds. Overall dimensions are Height = 6.3mm, and Diameter = 15mm. Designed and 3D printed by Ron Coon Resins..
Just $1.75 plus shipping.
ADAC_COMBO1
Air Deflector & Air Cleaner Combo
The ADAC_COMBO1 is a one HS_AD4 and one AC_10 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
ADAC_COMBO2
Air Deflector & Air Cleaner Combo
The ADAC_COMBO2 is a one HS_AD4 and one AC_11 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
ADAC_COMBO3
Air Deflector & Air Cleaner Combo
The ADAC_COMBO3 is a one HS_AD4 and one AC_12 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
ADAC_COMBO4
Air Deflector & Air Cleaner Combo
The ADAC_COMBO4 is a one HS_AD5 and one AC_10 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
ADAC_COMBO5
Air Deflector & Air Cleaner Combo
The ADAC_COMBO5 is a one HS_AD5 and one AC_11 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
ADAC_COMBO6
Air Deflector & Air Cleaner Combo
The ADAC_COMBO6 is a one HS_AD5 and one AC_12 money savings combo! Would look great on any 1:25 / 1:24 scale Late Model, Modified, or Street Stock build. Designed and 3D printed by Ron Coon Resins.
Just $3.25 plus shipping.
FC_16
Inline Fuel Filter
How cool is this! What a great detailed addition to any Strip, Street, or Track build. 3D Resin printed by Ron Coon Resins. Overall length is 15.3mm. Part number is for 3 filters on supports.
Just $1.80 per set plus shipping.
Item comes bare resin. Black washed for photo purposes.
FC_17
Inline Fuel Filter With Mounting Brackets
How cool is this! What a great detailed addition to any Strip, Street, or Track build. Mounting brackets are part of the filter and designed to mount on flat surface. 3D Resin printed by Ron Coon Resins. Overall length is 15.3mm. Part number is for 3 filters on supports.
Just $1.95 per set plus shipping.
Item comes bare resin. Black washed for photo purposes.
CARB_1
Holley Dominator Carb
CARB_1 Holley Dominator type carbs. These would look great on any motor, bench, shelf, etc.
Just $ .95 each plus shipping.
Item comes unpainted.
CARB_2
Holley 4150 Series Carb
CARB_2 Holley 4150 Series type carbs. These would look great on any motor, bench, shelf, etc.
PART NUMBER IS FOR 1 CARB
Just $1.65 each plus shipping.
CARB_3
Holley Type Carb
CARB_3 This Holley Type Carb is the biggest slamah jambah carb RCR has to date. Put one of these on your motor and you are going to need a bigger fuel cell!!!
PART NUMBER IS FOR 1 CARB
Just $1.75 each plus shipping.
CARB_4
Economy Carb
CARB_4 is universal, vacuum secondary, economy carb. This carb is a bit on the small side but has great detail. Overall dimensions are, Height = 3.8mm, Length = 9.8mm, and Width = 7.5mm
Just $ .75 each plus shipping,
CARB_5
Holley Double Pumper Carb
Take a look at these Holley Double Pumpers! The CARB_5 would be a great addition to any Street, Strip, or Track build. 3D resin printed by Ron Coon Resins. 1:25 / 1:24 scale. Overall dimensions are Length = 12mm, Height = 5.8mm, and Width = 8.2mm.
PART NUMBER IS FOR A PAIR OF CARBS
Just $3.50 per pair plus shipping.
CR_6
Gas Cooler Can
You have to keep that gas cool if you want those lower ET’s. This Mr. Gasket style gas cooler can has built in mounting bar and inlet and outlet bungs. Designed and 3D resin printed by Ron Coon Resins. Overall dimensions are ; Depth = 6.25mm, Width = 6.6mm, and Height = 7.25mm.
Just $1.80 per pair plus shipping.
VC_6
New Item Coming Soon
The VC_6 is a 1:25 scale SBC Circle Track claimer valve cover set. Designed and 3D printed by Ron Coon Resins. Sold as a pair. Breathers, breather tubes, and valve cover are 1 piece.
Note: Circle Track Cars use 2 breathers located on the left valve cover and none on the right valve cover.
Just $1.80 per pair plus shipping.
Item is washed for display purposes only, comes bare gray resin.
SPW_YELLOW
SPW_YELLOW Those other places want to charge you $4.00 for 2 feet of yellow spark plug wire – that’s just insane. Here at Ron Coon Resins, we have a better deal!
Just $5.00 for 10 feet plus shipping, all day every day!!!
SPW_ORANGE
Orange Spark Plug Wire – 10 feet
SPW_ORANGE Those other places want to charge you $4.00 for 2 feet of orange spark plug wire – that’s just insane. Here at Ron Coon Resins, we have a better deal!
Just $5.00 for 10 feet plus shipping, all day every day!!!
SPW_BLUE
Blue Spark Plug Wire – 10 feet
SPW_BLUE Those other places want to charge you $4.00 for 2 feet of blue spark plug wire – that’s just insane. Here at Ron Coon Resins, we have a better deal!
Just $5.00 for 10 feet plus shipping, all day every day!!!
SPW_BLACK
Black Spark Plug Wire – 10 feet
SPW_BLACK Those other places want to charge you $4.00 for 2 feet of black spark plug wire – that’s just insane. Here at Ron Coon Resins, we have a better deal!
Just $5.00 for 10 feet plus shipping, all day every day!!!
SPW_RED
Red Spark Plug Wire – 10 feet
SPW_RED Those other places want to charge you $4.00 for 2 feet of red spark plug wire – that’s just insane. Here at Ron Coon Resins, we have a better deal!
Just $5.00 for 10 feet plus shipping, all day every day!!!
MSD_1
Dual MSD Boxes on Mounting Panel
MSD_1 Dual MSD Boxes on mounting panel. Don’t want to run dual boxes? Then cut it in half, and with very little sanding, you’ll have two separate boxes!!!!
Just $1.25 each plus shipping.
MSD_2
3 Unit Electronic Control Panel
The MSD_2 is a 3 unit electronic control panel. Part number is for 1 unit.
Just $1.65 each plus shipping.
MSD_3
Generic Electronic Ignition Box
The MSD_3 is a Generic Electronic Ignition Box with awesome detail that will add that extra punch to your builds. Item measures 1/4″ x 1/4″, overall height is 1/8″.
Just $.49 each plus shipping.
MSD_4
MSD Digital 6AL Ignition Box
Check out the detail on these MSD boxes! A must have for any Street, Strip, or Track build. 3D resin printed by Ron Coon Resins. 1:25 / 1:24 scale.
Just $1.50 per pair plus shipping.
MSD_5
Mechanical Advance 8 Cylinder Distributor
If you are doing a V8 powered race car build the MSD_5 is for you. Real race cars have mechanically advanced distributors, not vacuum advanced distributors. This is the types of attention to detail that set us apart from other vendors. 1:25 / 1:24 scale printed by Ron Coon Resins. This item has guide holes for the spark plug wires but we suggest the builder drills them out for maximum depth. Micro drill bits will be needed to do so and we recommend no larger diameter bit than .55mm which is more than enough for or SPW spark plug wire.
Just $1.50 per pair plus shipping.
MSD_6
Vacuum Advance 8 Cylinder Distributor
If you are doing a V8 powered street build the MSD_6 is for you. Most street cars use vacuum advance distributors. These are the types of attention to detail that set us apart from other vendors. 1:25 / 1:24 scale printed by Ron Coon Resins. This item has guide holes for the spark plug wires but we suggest the builder drills them out for maximum depth. Micro drill bits will be needed to do so and we recommend no larger diameter bit than .55mm which is more than enough for or SPW spark plug wire.
Just $1.50 per pair plus shipping.
C_1
Old Fashioned Coil
The C_1 is a good Old Fashioned Coil, similar to an Accel Super Coil. Cast in 2 pieces to allow for better detailing.
Just $1.75 plus shipping.
OT_1
Dry Sump Oil Tank
The OT_1 is a 1:25 scale Dry Sump Oil Tank. Measures approximately 5/8″ in height and has molded in mounting pad on rear side of tank.
Just $2.25 each plus shipping.
OT_2
Dry Sump Oil Tank
The OT_2 is a 1:25 scale Dry Sump Oil Tank that is cast in two pieces that are self-centering. Measures 19/32″ in height.
Just $2.55 each plus shipping.
Item comes bare resin, painted for display purposes only.
OT_3
Moroso Style Dry Sump Oil Tank
It doesn’t get much cooler than the OT_3 Moroso style dry sump oil tank! Would make a great addition to any race car using a dry sump oil system. 3D resin printed by Ron Coon Resins. Overall dimensions are Height = 16mm and Diameter including breather = 13.5mm.
Just $2.25 each plus shipping.
Item comes on supports.
OT_4
Peterson Style Dry Sump Oil Tank
It doesn’t get much cooler than the OT_4 Peterson style dry sump oil tank! Would make a great addition to any race car using a dry sump oil system. 3D resin printed by Ron Coon Resins. Overall dimensions are Height = 16.4mm and Diameter including bung = 11.mm.
Just $2.25 each plus shipping.
VC_1
Moroso Style Big Block Chevy Valve Cover
The VC_1 is a 1:25 scale Moroso Style Big Block Chevy Valve Cover . Sold in pairs.
Just $1.30 per pair plus shipping.
Painted for photo purposes, item come bare resin.
VC_2
Big Block Chevy Race Valve Cover
The VC_2 is a 1:25 scale Big Block Chevy. Tall type race valve cover that would be used with a motor using roller rockers and high lift cam. Sold in pairs.
Just $1.30 per pair plus shipping.
Detailed for photo purposes, item come bare resin.
VC_3
Small Block Chevy Claimer Type Valve Cover
The VC_3 is a 1:25 scale Small Block Chevy Claimer Type Valve Cover. Perfect for just about any class, but especially any class that has a claim rule. Sold in pairs.
Just $1.30 each plus shipping.
Detailed for photo purposes, item comes bare resin.
VC_4
Valve Cover Breathers
Need some valve cover breathers for your Circle Track build, if so the VC_4 is for you. Come as a set of 4. Designed and 3D resin printed by Ron Coon Resins.
To achieve proper fitment cut at the base of the breather.
Note: Circle Track Cars use 2 breathers located on the left valve cover and none on the right valve cover.
Just $1.80 for a set of 4 breathers, plus shipping.
VC_5
Long Tube Circle Track Valve Cover Breather
The VC_5 is a Long Tube type of Circle Track Valve Cover Breather. The VC_5 was designed to give the builder options. You can trim to length, or drill valve cover and insert tube. Designed and 3d resin printed by Ron Coon Resins.
Note: Circle Track Cars use 2 breathers located on the left valve cover and none on the right valve cover.
Just $2.00 per set of 4 plus shipping.
VC_6
SBC Claimer Valve Covers
The VC_6 is a 1:25 scale SBC Circle Track claimer valve cover set. Designed and 3D printed by Ron Coon Resins. Sold as a pair. Breathers, breather tubes, and valve cover are 1 piece.
Note: Circle Track Cars use 2 breathers located on the left valve cover and none on the right valve cover.
Just $1.80 per pair plus shipping.
Item is washed for display purposes only, comes bare gray resin.
VC_7
SBC Claimer Valve Covers
The VC_7 is a 1:25 scale SBC Circle Track claimer valve cover set with raised bowtie logo. Designed and 3D printed by Ron Coon Resins. Sold as a pair. Breathers, breather tubes, and valve cover are 1 piece.
Note: Circle Track Cars use 2 breathers located on the left valve cover and none on the right valve cover.
Just $1.95 per pair plus shipping.
Item is washed for display purposes only, comes bare gray resin.
VC_8
Mickey Thompson 427 Valve Covers
The VC_8 is possibly one of the most iconic valve covers ever produced. If you were a big dog in the 70’s you had a pair of Mickey Thompson 427 cast aluminum valve covers with the “mushroom” breather. The VC_8 will defiantly draw attention to the engine compartment of any build! Designed by Nahuel Gomez, modified and 3d resin printed by Ron Coon Resins.
Note: Circle Track Cars use breathers located on the left valve cover and none on the right valve cover.
Just $1.99 per pair plus shipping.
OP_1
SBC Champ Wet Sump Circle Track Oil Pan
The OP_1 is a Low Profile SBC Champ style Wet Sump Circle Track Oil Pan, designed to replace the AMT NASCAR kit dry sump pans. Has indent to mark where the kit positioning pin would go (must be drilled) or can be filled with minimal amount of putty if needed for other applications.
Just $2.49 plus shipping.
Item painted for display purposes only, comes bare resin.
OP_2
SBC Champ Wet Sump Circle Track Oil Pan
The OP_2 is a 1:25 Deep Profile SBC Champ style Wet Sump Circle Track Oil Pan, designed to replace the AMT NASCAR kit dry sump. Has molded in drain plug and bead rolls on the bottom of the pan. Overall height is 7.25mm and overall width is 13.6mm. Part number is for 1 oil pan.
Just $2.99 each plus shipping.
Item comes bare resin.
INT_1
Brodix Style SBC Intake Manifold
The INT_1 is a 1:25 scale Brodix Style SBC Intake Manifold with a higher carb plenum than most kit intakes. Arrow molded in the top of the plenum points to the front of the intake for assembly purposes.
Just $1.75 plus shipping.
Item painted for display purposes only, item comes bare resin.
INT_2
SBC Edelbrock Victor Jr. Intake Manifold
The INT_2 is a 1:25 scale SBC Edelbrock Victor Jr. Style Intake Manifold that has been the choice of Circle Track racers for years! Arrow molded in the top of the plenum points to the front of the intake for assembly purposes.
Just $1.75 plus shipping.
Item painted for display purposes only, item comes bare resin.
INT_3
Small Block Ford Edelbrock /Brodix Intake Manifold
The INT_3 is a 1:25 scale Small Block Ford Edelbrock /Brodix Style Intake Manifold that has been the choice of Circle Track racers for years! Arrow molded in the top of the plenum points to the front of the intake for assembly purposes.
Just $1.75 plus shipping.
Item painted for display purposes only, item comes bare resin.
MAG_1
Magneto
The MAG_1 is an old school magneto. Use for builds that will not be using spark plug wires. Measurements are Height from collar = 8.5mm, Diameter = 4mm.
Just $.65 plus shipping.
MAG_2
Magneto
The MAG_2 is an old school magneto that is designed if spark plug wires are to be used exiting both sides of the magneto. Comes with hole that goes from side to side that is sized for Ron Coon Resins SPW_ spark plug wire. Designed and 3D resin printed by Ron Coon Resins. Measurements are Height from collar = 8.3mm, Diameter = 4mm.
Just $.69 plus shipping.
MAG_3
Magneto
The MAG_3 is an old school magneto that is designed if spark plug wires are to exit from a single side of the magneto. Comes with hole that exits one side only sized for Ron Coon Resins SPW_ spark plug wire. Designed and 3D resin printed by Ron Coon Resins. Measurements are Height from collar = 8.3mm, Diameter = 4mm.
Just $.69 plus shipping.
INT_4A
Fuel Injection Manifold/MAG_1
The INT_4A is a good old school fuel injection manifold. The INT_4A was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_1 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.1mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.75 plus shipping.
INT_4B
Fuel Injection Manifold/MAG_2
The INT_4B is a good old school fuel injection manifold. The INT_4B was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_2 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.1mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
INT_4C
Fuel Injection Manifold/MAG_3
The INT_4C is a good old school fuel injection manifold. The INT_4C was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_3 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.1mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
INT_5A
Fuel Injection Manifold/MAG_1
The INT_5A is a good old school fuel injection manifold with tube sock style outer filter. The INT_5A was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_1 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.5mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.75 plus shipping.
INT_5B
Fuel Injection Manifold/MAG_2
The INT_5B is a good old school fuel injection manifold with tube sock style outer filter. The INT_5B was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_2 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.5mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
INT_5C
Fuel Injection Manifold/MAG_3
The INT_5C is a good old school fuel injection manifold with tube sock style outer filter. The INT_5C was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_3 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 15.5mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
INT_6A
Fuel Injection Manifold/MAG_1
The INT_6A is a good old school fuel injection manifold with open velocity stacks. The INT_6A was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_1 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 14.7mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $4.25 plus shipping.
INT_6B
Fuel Injection Manifold/MAG_2
The INT_6B is a good old school fuel injection manifold with open velocity stacks. The INT_6B was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_2 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 14.7mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $4.45 plus shipping.
INT_6C
Fuel Injection Manifold/MAG_3
The INT_6C is a good old school fuel injection manifold with open velocity stacks. The INT_6C was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_2 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 14.7mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $4.45 plus shipping.
INT_7A
Fuel Injection Manifold/MAG_1
The INT_7A is a good old school fuel injection manifold with short bag type filters. The INT_7A was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_1 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 17mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.75 plus shipping.
INT_7B
Fuel Injection Manifold/MAG_2
The INT_7B is a good old school fuel injection manifold with short bag type filters. The INT_7B was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_2 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 17mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
INT_7C
Fuel Injection Manifold/MAG_2
The INT_7C is a good old school fuel injection manifold with short bag type filters. The INT_7C was designed and 3D resin printed to fit AMT Tobias and AMT NASCAR type kit motors, may fit other applications also. Comes with predrilled magneto hole and one MAG_3 magneto. Items overall dimensions are Length = 22mm, Width = 9.1mm, and Height = 17mm. Designed and 3D resin printed by Ron Coon Resins.
ITEM COMES MOUNTED TO SUPPORT BASE THAT MUST BE REMOVED BEFORE INSTALLATION.
Just $3.95 plus shipping.
WFC_ENG1
Small Block Chevy Motor
The WFC_ENG1 is nice 1:25 scale Small Block Chevy designed and 3D printed by WFC Motorsports. The WFC_ENG1 consists of 8 parts total; 2 headers, 1 Brinn/Bert style transmission, 1 bell housing, 1 air cleaner, 2 valve cover breathers (use on left side valve cover only for circle track applications, and a 1 piece motor assembly.
Just $12.00 plus shipping.
OA_1
1.5 Quart Accumulator
The OA_1 is a 1.5 Quart Accumulator that consists of four white resin pieces that must be assembled. It has an overall length of 18.22 mm or 23/32” Comes with one Moroso cylinder decal printed on white decal paper; must be final trimmed by builder.
Just $6.88 plus shipping.
Item is painted for display purposes only, comes bare white resin.
OA_1
3 Quart Accumulator
The OA_2 is a 3 Quart Accumulator that consists of four white resin pieces that must be assembled. It has an overall length of 27.75 mm or 1 3/32” Comes with one Moroso cylinder decal printed on white decal paper and must be final trimmed by builder.
Just $6.99 plus shipping.
Item painted for display purposes only, comes bare white resin.
RAD_1
Street Stock, Hobby Stock Radiator
The RAD_1 is for you builders who are looking for a big Street Stock, Hobby Stock style of Radiator. If it ran gas versus alcohol, this is the radiator for you. Core pattern is on both sides of radiator, no mounting holes or injection low spots. Filler neck is cast with radiator, cap is cast separate allowing the builder greater detailing options versus radiators available from others.
Overall dimensions:
- 30mm / 1 3/16”
- tank height = 18mm / 11/16”
- overall height (tank plus neck and cap) = 20mm / 13/16”
- overall width = 3mm / 1/8”
In 1:1 scale you would be basically looking at a 30” x 19” radiator.
Just $2.49 plus shipping.
Item detailed for photos purposes, item comes bare resin.
RAD_3
Vintage Modified Radiator
The RAD_3 is an excellent choice for those old school Modified builds. The RAD_3 comes with our radiator cap and upper and lower radiator hose indents. Will fit Tobias Modified kits. Overall height = 25.2mm, overall width = 27.8mm, and overall depth = 4.4mm.
Just $2.49 each plus shipping.
Item comes bare resin, painted and detailed for display purposes only.
RAD_4
One Piece Electric Fan With Shroud
The RAD_4 is a One Piece Electric Fan with Shroud that could be used as a push or pull set up. It is shown with our RAD_1 radiator, but could be used with many kit or scratch built radiators. Item measures as follows; 18.2mm x 16.8mm x 3.8mm . Designed and 3D resin printed by Ron Coon Resins. Radiator not included.
Just $1.99 plus shipping.
Item detailed for photo purposes only, comes bare gray resin.
HDR_1
SBC Header Flange
The HDR_1 is a 1:25 scale SBC header flange designed and 3D printed by Ron Coon Resins. Designed for those builders fabricating their own headers. Exhaust port holes are 1/16″. Simply position the flange to the head, mark the holes, remove flange, then drill hole in the head. Once holes are drilled and headers are fabricated attach flange to the head and insert header tubes thru flange and into the head.
Just $1.49 per pair each plus shipping.
HDR_2
Exhaust Heat Shield
The HDR_2 exhaust heat shield is must add detail for any circle track builder wanting exhaust to exit through body panel. Designed and 3D resin printed by Ron Coon Resins. Measures 9.8mm x 6.5mm. Drill panel hole to 11/64″ to allow shield to fit flush with the panel.
Just $.75 per pair plus shipping.
HDR_3
Vintage Headers
The HDR_3 is an old school style header. The HDR_3 could be used as BBC, BBF, SBF, 1:25, or 1:24 header. Tubes are open on the ends for greater detailing. Would be a great addition to any vintage Stock Car, Modified, Drag Car, etc. Tubes are perpendicular to header flange. Once mounted to cylinder head they will be angled approximately 23 degrees down. Designed and 3D resin printed by Ron Coon Resins. Dimensions are flange = 20.2mm x 3.6mm, back off header flange to end of tube is 17.5mm.
Just $1.99 per pair plus shipping.
HDR_4
Vintage Headers
The HDR_4 is an old school style header. The HDR_3 could be used as BBC, BBF, SBF, 1:25, or 1:24 header. Tubes are open on the ends for greater detailing. Would be a great addition to any vintage Stock Car, Modified, Drag Car, etc. Tubes are perpendicular to header flange. Once mounted to cylinder head they will be angled approximately 23 degrees down. Designed and 3D resin printed by Ron Coon Resins. Dimensions are flange = 20.2mm x 3.6mm, back off header flange to end of tube is 16.8mm.
Just $1.99 per pair plus shipping.
HDR_5
Exhaust Heat Shield
The HDR_5 exhaust heat shield is must add detail for any circle track builder wanting dual exhaust to exit through body panel. Designed and 3D resin printed by Ron Coon Resins. Measures 16mm x 8mm. Drill panel hole to 11/64″ to allow shield to fit flush with the panel. Part number is for 1 shield.
Just $.75 plus shipping.
HDR_6
Exhaust Heat Shield
The HDR_6 exhaust heat shield is must add detail for any circle track builder wanting dual exhaust to exit through body panel. Designed and 3D resin printed by Ron Coon Resins. Measures 14mm x 7.5mm. Drill panel hole to 11/64″ to allow shield to fit flush with the panel. Part number is for 1 shield.
Just $.75 plus shipping.
HDR_7
BBC Headers With Collectors
The HDR_7 is a generic BBC header with great detail right down to the hollowed out collectors. Designed by Nahuel Customs and 3D resin printed by Ron Coon Resins. The HDR_7 is a great addition to just about any type of build. Will fit 1:25 and 1:24 SBC kit motors. Overall dimensions are Length = 23mm, Height = 24mm, and Depth = 11mm.
Headers come as separate headers. Joined together for photo purposes only. Display stand not included.
Just $4.23 a pair plus shipping.
HDR_8
BBC Headers With Collectors
Headers come as separate headers. Joined together for photo purposes only. Display stand not included.
Just $4.23 a pair plus shipping.
HDR_9
SBC Headers With Collectors
Looking for that old school Hooker/Dynatech header look? If so the HDR_9 is for you. Designed and 3D resin printed by Ron Coon Resins. Header flange is the same as our popular HDR_1 SBC flange. Overall dimensions are Length = 33.3mm, Height = 15.8mm, and Width = 7mm.
Just $4.23 a pair plus shipping.
HDR_10
SBC Headers With Extended Collectors
Looking for that old school Hooker/Dynatech header look? If so the HDR_10 is for you. Designed and 3D resin printed by Ron Coon Resins. We took our popular HDR_9 header and added separate hollow extended elbow collectors that can be assembled at any desired angle, no more preset collector angles. Designed to be glued internally so there is no globby glue at the seam! Overall dimensions are Length = 49.3mm, Height = 15.8mm – 18.5mm, and Width = 7mm – 12.2mm.
Part number is for 2 headers and 2 collector extensions.
Just $5.73 a pair plus shipping.
HDR_11
Elbowed Collector Extensions
Check out the HDR_11. Want to extend your headers and add a turnout or turndown to them, if so the HDR_11 is for you! Designed and 3D resin printed by Ron Coon Resins. Great for all kinds of circle track, drag, rat rod, etc. builds. Overall dimensions are Length = 19.2mm, Diameter = 3.75mm, and Width = 5.9mm. Will work with Ron Coon Resins HDR_9 headers.
Just $1.99 per pair plus shipping.
HDR_12
SBC Headers With Collectors
Got an old school IMCA, UMP, Wissota Modified or Late Model build, if so the HDR_12 is what you need. Also makes a sweet header for Gassers, Rat Rods, etc.! Designed and 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 20mm, Height = 14.9mm, and Width = 19.3mm. 1:25/1:24 scale.
Just $4.23 a pair plus shipping.
HDR_13
SBC Headers With Collectors
Got an old school IMCA, UMP, Wissota Modified or Late Model build, if so the HDR_12 is what you need. Also makes a sweet header for Gassers, Rat Rods, etc.! Designed and 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 20mm, Height = 22.7mm, and Width = 14.5mm. 1:25/1:24 scale.
Just $4.23 a pair plus shipping.
HDR_14
SBC Headers With Collectors
The HDR_14 is a great all purpose SBC header. Would work great on just about any Circle Track, Drag, Off Road, etc. build. Designed and 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 31.6mm, Height = 14mm, and Width = 14.3mm. 1:25/1:24 scale.
Just $4.23 a pair plus shipping.
HDR_15
Vintage Trumpet Headers
The HDR_15 is a great header for those old school vintage Jalopy, Flathead, Rat Rod, and Drag builds. Overall dimensions are Length = 35mm, Height = 4.2mm, and Width = 19.5mm. Designed and 3D resin printed by Ron Coon Resins.
Just $2.99 a pair plus shipping.
WFC_HDR1
SBC Headers With Collectors
The WFC_HDR1 is a generic SBC header with great detail right down to the hollowed out collector down tubes. Designed and 3D resin printed by WFC Motorsports. The WFC_HDR1 is a great addition to just about any type of build. Overall dimensions are Length = 36.4mm, Height = 18mm, and Width = 10.2mm.
Headers come as separate headers. Joined together for photo purposes only.
Just $4.23 a pair plus shipping.
HDR_16
BBC Headers With Collectors
The HDR_16 is a great all purpose BBC header. Would work great on just about any Circle Track, Drag, Off Road, etc. build. 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 37.5mm, Height = 21mm, and Width = 5.5mm. 1:25/1:24 scale.
Just $4.23 a pair plus shipping.
HDR_17
BBC Headers With Extended Collectors
The HDR_17 is our HDR_16 headers with extended collectors / turndowns. Turndowns are separate so they can be positioned at any way builders desire and are pegged for easy positioning. Would work great on just about any Circle Track, Drag, Off Road, etc. build. 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 56.5mm, Height = dependent on extension position, and Width = 5.5mm. 1:25/1:24 scale.
Just $5.73 a pair plus shipping.
HDR_18
BBC Headers With Collectors
The HDR_18 is a great all purpose BBC header. Would work great on just about any Circle Track, Drag, Off Road, etc. build. 3D resin printed by Ron Coon Resins. Overall dimensions are Length = 21.6mm, Height = 17.3mm, and Width = 6.6mm. 1:25/1:24 scale.
Just $4.23 a pair plus shipping.
HC_1
Header Collectors
HC_1 Header Collectors? Yep we have them. Whether you want to add them to some existing kit headers or you are scratch building, these are the icing on the cake!
Sold in pairs.
Just $1.00 per pair plus shipping.
LP_1
Motor Lift Plate
The LP_1 is a motor lift plate used by most racers to remove and install motors. It also serves as an intake block off plate for motor storage.
Designed and 3D resin printed by Ron Coon Resins.
Intake not included, black washed for photo purposes only. Items comes bare gray resin.
Just $.75 each plus shipping.
TR_PG
GM Powerglide Transmission
The TR_PG is a GM Powerglide Transmission. This transmission has been used for for years in Circle Track cars, Drag cars, Pull trucks, etc. Case is 1 piece with no seam or flash, with the pan casted separately.
Just $3.75 plus shipping.
Item is painted for display purposes only, comes bare resin.
TR_1
Flywheel and Clutch
How cool is this? This one piece flywheel / clutch would make a great addition to any diorama whether installed on a motor or sitting on a bench. Dimensions are 14mm x 2.8mm. Designed by Motabas Yen and 3D resin printed by Ron Coon Resins.
Just $1.50 per pair plus shipping.
Engine block and oil pan not included.
TR_2
Gen 2 Bert Transmission & Bellhousing
WOW! Take your build to the next level with the TR_2. Item is 1:25 scale and comes in 3 pieces; 1 transmission with tail stock, 1 bellhousing with oil and fuel pump, and 1 starter. 3D resin printed by Ron Coon Resins and is shipped on supports.
Overall dimensions are; length = 27.8mm, width = 18.5mm, and height = 15mm.
Just $4.99 plus shipping.
TR_PG
GM Powerglide Transmission
The TR_PG is a GM Powerglide Transmission. This transmission has been used for for years in Circle Track cars, Drag cars, Pull trucks, etc. Case is 1 piece with no seam or flash, with the pan casted separately.
Just $3.75 plus shipping.
Item is painted for display purposes only, comes bare resin.